3
SMT AssemblyDFA & Yield•Oct 22, 2026•6 min read

Automated Pin-in-Paste (PiH) Reflow: Stencil Aperture Volume Calculation & Solder Fillet Reliability

ER

Elena Rostova

Lead SMT Process Specialist

Reviewed by: SMT Production Committee
DFA & Yield
Pin-in-Paste (Through-Hole Reflow) allows mixed-technology PCBA designs to bypass wave soldering and selective soldering entirely. By depositing sufficient solder paste volume directly into through-hole barrels using custom overprinted step-up stencils, full 100% IPC-A-610 Class 3 barrel fill is achieved in the primary SMT convection reflow cycle.

1. Paste Volume Calculation for Through-Hole Barrels

Solder paste shrinks by approximately 50% in volume after flux evaporation and metal coalescing during reflow. Therefore, the printed wet paste volume must equal twice the net solid solder volume required to fill the barrel annular space and form top and bottom fillets.

The mathematical equation: V_paste = 2 * [ V_hole - V_pin + V_fillet_top + V_fillet_bottom ]. When pad dimensions are tight, overprinting onto non-wettable solder mask or step-up stencils (180µm) provides the necessary surplus volume without causing bridging.

Key Engineering Takeaways

  • Wet paste print volume must account for 50% flux vehicle shrinkage.
  • Overprinting over soldermask pulls back cleanly into the barrel via surface tension.

2. Thermal profiling for High Thermal-Mass Connectors

Large high-current automotive connectors and shrouded terminal blocks act as heat sinks during reflow, causing cold solder joints and insufficient barrel penetration if reflow soak times are insufficient.

We employ 10-zone nitrogen reflow ovens with independent top and bottom convection flow, extending the soak zone (150°C-180°C) to 90 seconds to equilibrate connector pin temperatures before liquidus.

Key Engineering Takeaways

  • Nitrogen atmosphere improves wetting speed on tinned and gold-plated leads.
  • Extended soak duration prevents temperature deltas between SMDs and large connectors.

Pin-in-Paste Stencil & Hole Tolerance Guidelines

Optimal geometric ratios for 100% IPC Class 3 solder fill in a single reflow pass.

Design ParameterCommercial TargetHigh-Reliability Class 3 TargetEngineering Notes
Pin-to-Hole Diameter RatioLead Diameter + 0.35 mmLead Diameter + 0.20 mm to + 0.25 mmMinimizes required paste volume and solder voids
Barrel Solder Fill Percentage> 75% vertical fill100% full vertical fill with continuous filletsVerified via automated 3D X-Ray (AXI)
Stencil Technology120µm flat laser cutStep-up laser stencil (150µm-180µm local)Deposits targeted solder volume without bridging adjacent SMD pads
Tags:#Pin-in-Paste#Through-Hole Reflow#Aperture Design#Solder Fillet#DFA
Fabrication Ready

Need Prototype for this Design?

Turn your high-speed schematics into reality with ChipPCBA. Automated DFM, fast turnaround from 24h, and IPC Class 2/3 inspection standard. Free DFM analysis with every instant quotation.

Related Engineering Articles

View all
SMT Assembly9 min read

Selective & Nitrogen Wave Soldering for Mixed Technology PCBA: Solder Pot Dynamics & Dross Elimination

Optimizing selective wave soldering on high-density double-sided SMT boards: nitrogen shroud purity, wettability on thick copper ground planes, and eliminating solder bridging on 1.27mm connectors.

SMT Assembly8 min read

Design for Assembly (DFA): Best Practices for 0.25mm Pitch BGA and 01005 Components

Essential solder paste aperture ratios, pad land patterns, solder mask dam clearances, and thermal relief design for 0.25mm Pitch BGA and ultra-fine pitch components.

SMT Assembly10 min read

AI 3D AOI & X-Ray Nanometer Tomography: Detecting 0.25mm BGA Micro-Voids and Head-in-Pillow Defects

Deep dive into 3D moiré fringe projection optical inspection and 160kV nano-focus computed tomography (CT) for eliminating Head-in-Pillow (HiP) defects and enforcing IPC-A-610 Class 3 void thresholds.