3
End-to-End Electronics Fabrication & Assembly Standards

PCB & PCBA Manufacturing Capabilities Matrix

Explore ChipPCBA's full-spectrum fabrication limits and assembly capabilities. From rapid 24-hour prototype boards to high-layer count HDI and aerospace-grade turnkey assemblies, our state-of-the-art facilities guarantee uncompromising IPC Class 3 quality.

Max Layer Count
64 Layers
Any-Layer HDI & Blind/Buried Vias
Min Line / Space
2.0 / 2.0 mil
0.05mm ultra-fine pitch trace
Min Laser Micro-Via
0.075 mm
LPKF German UV laser drilling
SMT Placement Precision
01005 (0402m)
Panasonic NPM-D3 dual-gantry

Comprehensive Manufacturing Comparison Table

Side-by-side specification limits across rigid, flex, and assembly technologies.

IPC-A-600 / IPC-A-610 Class 3 Ready
Technical ParameterStandard PCBAdvanced PCB (HDI)Flex PCB (FPC)Rigid-FlexTurnkey PCBA
Layer Count
Blind and buried vias supported on all multilayer options.
1 - 8 LayersUp to 64 Layers (Any-Layer HDI)1 - 8 Layers (Single / Double / Multi)2 - 20 Layers (Rigid + Flex cores)Double-sided SMT & THT Mixed
Board Thickness
Custom core and prepreg stackups available upon request.
0.4mm - 3.2mm (±10%)0.2mm - 6.0mm (±8%)0.05mm - 0.5mm (Ultra-thin)0.3mm - 3.5mm (Selective flex)0.2mm - 4.5mm carrier support
Min Trace Width / Spacing
Laser Direct Imaging (LDI) applied for sub-3mil line tolerance.
3.5 mil / 3.5 mil (0.09mm)2.0 mil / 2.0 mil (0.05mm)2.0 mil / 2.0 mil (0.05mm)2.5 mil / 2.5 mil (0.065mm)01005 (0402 metric) & 0.25mm pitch
Min Hole Size (Mechanical / Laser)
Via-in-Pad Plated Over (VIPPO) with epoxy filling available.
0.2mm (8 mil) Mechanical0.075mm (3 mil) UV Laser Micro-via0.1mm (4 mil) Laser / 0.2mm Mech0.075mm (3 mil) Laser / 0.15mm MechPin-through-hole down to 0.4mm
Max Aspect Ratio
Continuous copper plating thickness ≥ 25μm (IPC Class 3).
10:1 (Thickness to Hole Dia)16:1 (High-aspect deep plating)6:112:1N/A (PCB dependent)
Surface Finish Options
Gold finger plating with 30 u" hard gold and chamfering.
HASL Lead-Free, ENIG (1-3 u")ENIG (3-5 u"), ENEPIG, Hard GoldImmersion Gold (ENIG), Immersion TinENIG, ENEPIG, Selective Hard GoldOSP, ENIG, HASL compatible
Impedance Control Tolerance
TDR coupon testing included with micro-section report.
±10% (Single / Diff pairs)±5% (Tight high-speed control)±10% (Microstrip / Stripline)±7% (Differential across seam)Signal integrity verified
Base Materials & Laminates
Shengyi, ITEQ, Rogers, Panasonic Megtron 6 materials stocked.
Standard FR-4 (Tg 130-140°C)High-Tg FR-4 (Tg 170-180°C), Rogers, PTFEPolyimide (PI), Adhesive / AdhesivelessHigh-Tg FR-4 + DuPont Polyimide (PI)FR-4, Metal Core, Ceramic, Flex
Component SMT Pitch & Size
Panasonic NPM-D3 mounters with Koh Young 3D SPI and AOI.
N/A (Bare Board)N/A (Bare Board)N/A (Bare Board)N/A (Bare Board)01005 (0402 metric), 0.25mm BGA/QFN
Testing & Inspection Standards
IPC-A-600 / IPC-A-610 Class 3 compliant quality reports provided.
100% AOI & Flying Probe E-Test100% AOI, Dedicated Fixture E-Test, TDR100% AOI, Open/Short Electrical Test100% AOI, X-Ray, High-Pot Test3D SPI + 3D AOI + 3D X-Ray + FCT
Official Engineering Documentation

Download ChipPCBA Manufacturing Capabilities PDF Manual

Get our comprehensive 36-page DFM engineering handbook covering layer stackup guidelines, high-speed differential impedance calculation tables, copper thickness derating charts, and IPC Class 3 quality inspection criteria.

Ready to verify and fabricate your design?

Upload your Gerber or BOM now for an automated DFM audit and instant volume quote.