3
ChipPCBA Standard Stackup & Controlled Impedance Guide

ChipPCBA 标准叠层与受控阻抗设计指南

官方标准 4 层、6 层、8 层压合结构(7628 / 2116 / 3313 / 1080 半固化片体系),提供精准介质厚度、铜箔规格、介电常数 Er 与 50Ω 单端、90Ω/100Ω 差分线宽速查推荐,支持一键载入阻抗仿真计算器与在线报价联动。

显示单位:

ChipPCBA 4-Layer (1.6mm / 7628 Prepreg)

ChipPCBA 推荐压合体系

标准压合总厚度:1.6 mm (±10% 公差) | 外层/内层铜厚:1.0 oz (35 µm)

压合物理层结构 (Cross-Section)介质厚度 / 铜厚 (Er)
L1
L1: Top CopperTop Signal & Components
Electrodeposited Copper (ED Cu)
1.38 mil1 oz (35 µm)
PP
Prepreg PP (7628)Dielectric Layer (Bonding Sheet)
FR-4 Prepreg 7628 (Resin Content ~50%)
8.27 milEr = 4.4
L2
L2: Inner GroundSolid Ground Reference (GND Plane)
Rolled-Annealed Copper Foil
1.38 mil1 oz (35 µm)
Core
Inner Core DielectricRigid Structural Core Substrate
FR-4 Laminate Core (Cured Glass Fabric)
39.37 milEr = 4.5
L3
L3: Inner PowerPower Distribution Plane (VCC/VDD)
Rolled-Annealed Copper Foil
1.38 mil1 oz (35 µm)
PP
Prepreg PP (7628)Dielectric Layer (Bonding Sheet)
FR-4 Prepreg 7628 (Resin Content ~50%)
8.27 milEr = 4.4
L4
L4: Bottom CopperBottom Signal & Test Points
Electrodeposited Copper (ED Cu)
1.38 mil1 oz (35 µm)
图例说明:
Top Copper / Inner / Bottom Copper (铜箔)
Prepreg PP 半固化片胶片
Inner Core 固化芯板基材

工艺特色与压合说明

Most economical 4-layer standard stackup widely utilized for IoT, consumer electronics, and industrial MCU boards. Features thick 7628 prepreg (0.21mm) between outer signal and inner ground planes.

Standard 1.6mm finished thickness with 1oz outer & inner copper
Cost-effective high-yield lamination process with 7628 prepreg glass cloth
Nominal dielectric constant Er ≈ 4.4 at 1 GHz
Optimal for signals up to 1.5 GHz and standard MCU microstrip fanouts
工程工具与报价无缝联动

无需重新手工输入板厚、铜厚与介质厚度。点击下方按钮即可将当前叠层参数直接带入 IPC 阻抗求解器或 ChipPCBA 智能在线报价系统。

ChipPCBA DFM 翘曲控制与对称性建议

根据 IPC-TM-650 标准,多层板在回流焊过程中若铜箔残铜率或芯板介质层分布不对称,极易发生弓曲(Bow)与扭曲(Twist)。ChipPCBA 标准叠层均采用镜像对称压合设计,保障翘曲率 ≤ 0.75%(SMT 贴片标准)。

50Ω 单端与 90Ω / 100Ω 差分线宽/间距推荐速查表

基于 IPC-2141A / Wadell 闭合公式,标准 FR-4 (Er ≈ 4.2~4.4) 1oz 铜箔推荐布线参数

公差标准: ±10% (精准定制 ±5%)
走线类型 (Topology)目标特征阻抗推荐线宽 (Trace Width)推荐线距 (Spacing S)参考地平面典型应用协议 / 备注
Single-Ended Microstrip50Ω14.5 mil(0.368 mm)N/A (单端走线)L2 (GND)General 50Ω RF / digital traces (Wi-Fi, Bluetooth, SPI)
Differential Microstrip90Ω10.0 mil(0.254 mm)7.0 mil(0.178 mm)L2 (GND)USB 2.0 Full/High-Speed D+/D- differential routing
Differential Microstrip100Ω8.0 mil(0.203 mm)7.0 mil(0.178 mm)L2 (GND)100Base-TX Ethernet, RS-485 differential pairs
TDR 阻抗在线全检与出货报告

ChipPCBA 配备专业时域反射仪(TDR)。对有阻抗控制要求的订单,在板边附带标准阻抗测试条(Coupon),每批次提供出厂 TDR 阻抗测试波形与合格报告。

阻焊油墨对阻抗的频偏补偿

表层绿油阻焊(Solder Mask)厚度约 15~25 µm(Er ≈ 3.5),通常使微带线阻抗降低 2~3Ω。ChipPCBA CAM 工程师在工程制作时会自动进行线宽预补偿。

高频低损耗材料自由切换

除标准 FR-4(生益 S1000-2 / 南亚)外,ChipPCBA 支持 Rogers RO4350B、RO4003C 以及生益高 Tg170 / 无卤素板材混压,满足 5G 毫米波及雷达天线低损耗需求。